Raccords d'inondation et de vidange IWS 25 mm

Economisez £2.26
IWSSKU: 14144

Minuteur: Complete Pro Straight
Prix:
Prix réduit£4.04 Prix normal£6.30

Taxes incluses Frais de port calculés au paiement

<p>Gagnez%20[points_amount]%20lorsque%20vous%20achetez%20cet%20article.</p>

Frequently Asked Questions

How many washers and nuts do I need for each IWS 25mm Pro fitting?

Two rubber washers and one plastic nut for every fitting. Our AutoDrain brain page says the same when it tells you to buy 6 straights, 6 nuts and 12 washers to fit 25mm outlets on a Standard bucket. The washers and nut are separate options on this page, so add them for each straight, tee or elbow in your basket.

Which IWS 25mm Pro fitting do I need, straight, tee or elbow?

Use a straight where a pipe meets a pot, a tee where the pipe carries on to the next pot, and an elbow for the last pot at the end of the run. That follows the part descriptions above: the tee sits in the middle of a pipe run to extend it, and the elbow finishes the run and turns the corner into the last outer pot. Not sure how your run is laid out? Ask us before you order.

Will IWS 25mm Pro fittings fit my 16mm IWS Standard system?

Not as they come, because these are 25mm Pro parts and the Standard system runs on 16mm fittings. You can convert, though. The Standard AutoDrain bucket has glands you can remove and swap for 25mm fittings, and our IWS 16mm Drain Fittings page lists a female hose tail that connects 25mm Pro fittings to 13mm standard pipe. For a plain 16mm run, you want the 16mm fittings instead.

What does the IWS Pro individual pot filter do?

It sits inside the pot and filters out large particles, so they do not get washed back into your reservoir. It is 110 mm long with a 25 mm female thread, and it attaches to a 1 inch male drain hose tail, or to a 16 mm reducing grommet on older 16 mm systems. The cage is hard-wearing plastic with a copper mesh that repels roots and limits their ingress.

Can I buy IWS Pro washers and nuts on their own?

Yes. The Pro Rubber Washer and Pro Plastic Nut are their own options on this page, so you can order just the one you lost. Remember that a fitting takes 2 washers and 1 nut, and it is worth adding a spare or two because they are cheap and small.

What size pipe do IWS 25mm Pro fittings fit?

25mm. The barbed end goes into 25mm pipe and the threaded end goes inside the pot. Our 25mm Black IWS Pipe is 25mm inner diameter and comes by the metre or as a 30m roll.

Description

Choisissez parmi une sélection de composants IWS authentiques de 25 mm qui sont parfaits pour mettre à niveau votre système ou remplacer des pièces perdues ou endommagées.

Pièce droite barbelée

Un droit universel qui s'adapte sur les pots de votre système IWS Hydroponics. Les barbes à une extrémité de la pièce droite la maintiennent très solidement dans la tuyauterie. L'extrémité à vis se fixe solidement à l'intérieur de vos pots.

Pièce en T barbelée

La pièce en T universelle s'adapte au milieu d'un tronçon de tuyauterie pour prolonger le tuyau. Les barbes à une extrémité du joint en T universel le maintiennent très solidement dans la tuyauterie. L'extrémité à vis se fixe solidement à l'intérieur de vos pots.

Coude barbelé

Le coude universel s'adapte à l'extrémité de la tuyauterie pour terminer le tuyau et fournir un moyen pratique de "tourner le coin" dans le dernier pot extérieur de votre système IWS Hydroponics. Les barbes à une extrémité du coude universel le maintiennent très solidement dans la tuyauterie. L'extrémité à vis se fixe solidement à l'intérieur de vos pots.

Écrou en plastique

L'écrou en plastique IWS 25 mm doit être utilisé avec votre raccord, rondelle et pot IWS 25 mm pour assurer une étanchéité parfaite.

Une rondelle en caoutchouc

La rondelle IWS 25 mm doit être utilisée de chaque côté de votre raccord et pot IWS 25 mm pour assurer une étanchéité parfaite.

Filtre à pot individuel

Le filtre d'inondation et de vidange en ligne IWS mesure 110 mm de long et possède un filetage femelle de 25 mm qui se fixe à une queue de tuyau de vidange mâle de 1 "de diamètre ou à un œillet réducteur de 16 mm pour les anciens systèmes de 16 mm.

Le filtre se trouve à l'intérieur du pot et agit pour filtrer les grosses particules, les empêchant de retourner dans le réservoir. Le filtre est une cage en plastique résistant avec un maillage en cuivre qui repousse les racines, limitant leur pénétration. Le

Frequently Asked Questions

You may also like

Recently viewed